Phase resistance is a fundamental electrical parameter checked during brushless DC (BLDC) motor manufacturing and quality inspection. For a three-phase motor, engineers typically measure the resistance between three terminal pairs: A–B, B–C, and C–A. For a symmetrically designed winding, these readings are expected to be reasonably close. However, observing a small difference does not automatically indicate a manufacturing defect.
Phase resistance balance is a useful diagnostic tool only when the measurement itself is trustworthy. The measured value can be influenced by test leads, probe contacts, winding temperature, and instrument resolution. The goal is not to obtain three perfectly identical numbers, but to determine whether the observed variation represents a genuine electrical imbalance inside the motor.
Therefore, before concluding that a motor is faulty, it is essential to understand what the measurement represents, how to perform it reliably, and how to interpret the results within the context of the motor's design and operating conditions1.
Why Three-Phase Resistance Balance Matters in a BLDC Motor
In a symmetrically wound three-phase BLDC motor, each phase winding should have nearly identical electrical characteristics by design. Measuring the terminal-to-terminal resistance is a practical way to screen for potential inconsistencies.
Depending on the severity of the defect and the motor drive strategy, these variations may affect phase current response, copper losses, and localized heating. However, the actual impact on torque ripple, efficiency, and operating stability must be evaluated under the intended drive and load conditions.
A significant deviation among the three line-to-line resistance readings can suggest underlying manufacturing or connection issues, such as:
- Incorrect wire diameter or different conductor lengths
- Variations in the number of turns per winding
- Poor-quality solder or weld joints at the terminals
- Damaged conductors or lead wires
For example, at similar winding currents, a higher-resistance winding may experience greater copper losses (I²R) and localized heating. While many closed-loop drivers can adjust current to compensate for electrical asymmetry to some degree, a significant underlying imbalance may still affect efficiency and long-term reliability, depending on the operating conditions.
What Do AB, BC, and CA Resistance Measurements Actually Represent?
When you measure the resistance between the three external terminals (e.g., A, B, and C) of a BLDC motor, you are measuring the line-to-line resistance. Comparing these three values (AB, BC, CA) is a practical check for winding balance. However, interpreting these values to determine the resistance of a single phase winding requires knowing the internal connection scheme.
Even without knowing whether the motor is Star or Delta wound, you can still compare the three line-to-line resistance measurements for consistency. A significant difference may indicate an electrical imbalance. However, calculating individual winding resistance or investigating winding-specific faults requires an understanding of the internal connection configuration.
For a balanced motor, the relationship is:
-
Star (Wye) Connection: The windings meet at a common neutral point. The resistance between any two terminals is the sum of two phase resistances.
R(L–L) = 2 × R(phase)
-
Delta Connection: The windings are connected end-to-end. The resistance between any two terminals is one winding in parallel with the other two in series.
R(L–L) = (2/3) × R(winding)
| Measurement Item | Star / Wye | Delta |
|---|---|---|
| Connection | Common neutral point | Closed triangle |
| Terminal-Pair Measurement | Two phase windings in series | One winding in parallel with two series windings |
| Balanced Relationship | R(L–L) = 2 × R(phase) | R(L–L) = (2/3) × R(winding) |
| Directly Measures One Winding? | No (requires a separate line-to-neutral measurement) | No |
It is important to distinguish between comparing line-to-line values for balance and using them to calculate the resistance of an individual winding. This distinction also relates to the broader electrical differences between Star and Delta winding configurations, which affect the voltage, current, and effective motor constants seen by the driver.
Why Milliohm-Level Resistance Is Difficult to Measure Accurately
Some compact BLDC motors, particularly low-voltage, high-current designs, have winding resistances in the milliohm (mΩ) range. At this level, the measurement system itself can become a significant source of error.
A small measured resistance difference cannot be treated as a winding defect until errors from test leads, contacts, and instrument resolution are minimized. For accurate measurement of low-resistance windings, a four-wire Kelvin method is strongly recommended.
- Two-Wire Measurement: A standard multimeter's reading includes the resistance of the test leads and the probe contacts, which can fluctuate and introduce significant error.
- Four-Wire (Kelvin) Measurement2: This method uses one pair of leads to inject current and a separate pair to sense voltage directly across the motor terminals. It largely eliminates the influence of current-lead resistance and the associated contact voltage drops outside the voltage-sensing points.
However, four-wire measurement does not eliminate the resistance of internal motor connections located between the voltage-sensing points. This means that internal lead wires, solder joints, and winding connections may still contribute to the measured terminal resistance.
For reliable results, the voltage-sensing points should be positioned as close as practical to the specified motor terminals, and the test current should be selected to provide sufficient resolution without causing significant winding self-heating.
For very low-resistance measurements, thermoelectric voltage offsets may also affect accuracy. Where necessary, an instrument with current-reversal or offset-compensation capability can help reduce these errors.
How Winding Temperature Changes Resistance Measurements
The electrical resistance of copper changes significantly with temperature. This is one of the most common and often overlooked sources of variation in resistance measurements.
A uniform temperature increase generally raises all three resistance readings together and does not, by itself, indicate worsening phase imbalance. The main challenge with temperature is ensuring that comparisons—whether between phases, between motors, or against a specification—are made under equivalent thermal conditions.
The resistance of a copper winding at a given temperature (T) can be approximated using the formula:
R(T) = R(20°C) × [1 + α × (T − 20)]
Here, R(20°C) is the resistance at 20°C, T is the winding temperature in °C, and α is the temperature coefficient of copper (approximately 0.00393/°C)3.
For example, a winding with a resistance of 50.0 mΩ at 20°C will have a resistance of approximately 52.0 mΩ at 30°C. This nearly 4% increase could be mistaken for a deviation from the nominal resistance specification if temperature is not considered.
For accurate comparisons, either allow the motor to thermally stabilize at a known ambient temperature or correct the measurements to a common reference temperature. Where the internal winding temperature cannot be measured directly, an external temperature reading should only be used as a winding-temperature estimate when the thermal conditions support that assumption.
What Can Unequal Phase Resistance Reveal About Manufacturing Defects?
Once measurement and temperature variables are controlled, a verified and significant resistance imbalance can point to genuine manufacturing issues.
Resistance imbalance helps identify where to investigate, but it rarely proves a specific failure mechanism by itself. For example, a turn-to-turn short may not create a large enough change in DC resistance to be reliably detected by this method alone.
Potential root causes include:
- Winding Variation: Use of incorrect wire gauge, inconsistent turn counts between phases, or physical damage to conductors during the winding process.
- Connection Defects: Poorly executed solder joints or welds at the termination points can introduce significant, non-uniform resistance.
- Process Variations: Inconsistent winding or termination processes can introduce resistance differences within a motor. Changes in wire materials or production settings may also cause shifts in the overall resistance of different production batches.
A consistent resistance imbalance is a reason to investigate the winding and assembly process further. However, a motor with three similar resistance readings may still have other electrical defects that require insulation, inductance, back-EMF, or functional testing to identify.
How Much Phase Resistance Difference Is Acceptable?
There is no universal percentage that defines an acceptable resistance spread for all BLDC motors. A fixed limit like "less than 2%" is arbitrary and may be too loose for a precision motor or too tight for a commercial-grade product.
A calculated percentage describes the observed variation; it does not independently define a quality limit. The proper limit must be defined in the product specification, accounting for the motor's design, its resistance magnitude, and the uncertainty of the measurement system.
A common way to quantify the variation is to calculate the spread:
Spread (%) = [(R(max) − R(min)) / R(avg)] × 100
For example, with temperature-corrected Kelvin measurements of AB = 180 mΩ, BC = 181 mΩ, and CA = 190 mΩ, the average is 183.7 mΩ and the spread is approximately 5.4%.
This number is an observation, not a verdict. Its acceptability depends on the limits established in the motor's engineering specification. The same principle applies when defining DC motor acceptance criteria before sample approval: measurement conditions, acceptance limits, and decision rules should be established before the results are used to approve or reject a motor4.
How to Diagnose Abnormal BLDC Phase Resistance Step by Step
If you suspect a phase resistance issue, follow a systematic process to ensure your diagnosis is based on reliable data.
A proper diagnosis starts with isolating the motor and using a reliable measurement technique. The goal is to separate measurement artifacts from true electrical asymmetry before comparing the results to the official specification.
- Isolate the Motor: Safely disconnect the motor from the driver electronics.
- Measure All Three Pairs: Use a four-wire Kelvin method5 to measure the AB, BC, and CA terminal resistances.
- Check Repeatability: Disconnect and reconnect the probes to ensure the readings are stable and not dependent on contact pressure.
- Confirm Temperature: Establish a suitable winding-temperature estimate or allow the motor to stabilize at a known ambient temperature. Correct the readings to a 20°C reference if necessary.
- Confirm Winding Configuration: If calculating individual winding resistance, use the correct relationship for Star or Delta6.
- Compare With Specification: Check the absolute resistance values and the calculated spread against the approved product specification.
- Investigate Related Symptoms: If an imbalance is confirmed, check for secondary symptoms such as abnormal phase currents, excessive temperature rise, or unusual vibration during operation7.
| Observed Result | Possible Cause | Recommended Check |
|---|---|---|
| All three readings consistently high | Elevated winding temperature, incorrect winding variant, or measurement setup error | Verify temperature, motor part number, sense-point placement, and instrument setup |
| One or more terminal-pair readings deviate | Winding or connection asymmetry, or measurement contact error | Repeat all three measurements and inspect terminal connections |
| Readings change with probe pressure | Unstable probe contact or dirty terminals | Clean terminals and inspect the test fixture |
| Resistance rises after operation | Normal winding heating | Allow motor to cool to ambient temperature |
| Equal resistance but abnormal current | Driver, magnetic, or other motor fault not revealed by DC resistance | Perform back-EMF, inductance, and functional tests |
| Unstable or open-circuit reading | Broken conductor or intermittent connection | Inspect terminals, lead wires, and internal joints |
What OEM Engineers Should Provide for Phase Resistance Evaluation
When consulting a motor supplier about a potential resistance issue, providing comprehensive test data is essential for an effective analysis.
To properly analyze resistance readings, your motor supplier needs to know not just the three numbers, but also how they were measured and the motor's thermal conditions. Internal winding configuration becomes particularly important when investigating individual winding resistance or locating potential faults.
| Required Information | Why It Matters |
|---|---|
| AB, BC, and CA Resistance Readings | The core data for calculating spread |
| Winding Configuration | Required for calculating individual winding resistance and investigating winding-specific faults |
| Measurement Temperature8 | Needed to evaluate temperature effects and apply appropriate corrections |
| Measurement Method | Determines measurement accuracy (2-wire vs. 4-wire) |
| Instrument Resolution/Accuracy | Defines the limits of measurement reliability |
| Motor Model and Revision | Ensures comparison against the correct specification |
| Related Symptoms (e.g., Current) | Provides context about operational impact |
| Batch or Sample Information | Helps investigate production consistency |
Share your three line-to-line resistance readings, winding configuration if known, test temperature, and measurement method. BODENMOTION's engineering team can help review the results and identify whether further winding or connection testing is needed.
Conclusion
Phase resistance balance is a useful diagnostic parameter in DC brushless motor manufacturing and quality inspection. Significant differences between the three terminal-pair readings may indicate winding, connection, or assembly problems. However, small variations can also result from measurement leads, probe contacts, instrument limitations, and temperature differences. A trustworthy conclusion therefore requires consistent test conditions, an understanding of the relevant winding configuration, and a measurement method suitable for the motor's resistance range.
For OEM engineers, equal resistance should be treated as one part of electrical quality verification rather than proof of complete motor health. Comparing corrected AB, BC, and CA measurements against product-specific acceptance criteria—and investigating related symptoms where necessary—provides a more reliable basis for sample approval and production troubleshooting. For projects requiring motor selection or electrical performance evaluation, explore BODENMOTION's DC motor solutions or contact our engineering team at info@bodenmotion.com to discuss your application requirements.
FAQ
Q1: Should all three phase resistance readings of a BLDC motor be equal?
For a balanced three-phase winding design, the three terminal-pair resistance readings should be reasonably close under equivalent measurement conditions. Small differences may reflect normal manufacturing tolerances or measurement uncertainty.
Q2: How do I measure the resistance of a three-phase BLDC motor?
With the motor safely isolated from its drive electronics, measure resistance between the AB, BC, and CA terminals using an appropriate low-resistance measurement method (ideally four-wire Kelvin). Record the measurement temperature and confirm the winding configuration when individual winding resistance needs to be calculated.
Q3: Why does my BLDC motor show different phase resistance readings?
Possible causes include genuine winding variations, inconsistent solder joints, conductor damage, or measurement-related factors such as probe contact resistance, instrument limitations, and temperature differences between readings.
Q4: Is a normal multimeter accurate enough for BLDC phase resistance testing?
For windings with resistance in the milliohm range, a standard two-wire multimeter is often not accurate enough, as its own lead and contact resistance can obscure the true value. A four-wire Kelvin measurement system is strongly preferred.
Q5: Does equal phase resistance mean the BLDC motor is healthy?
Not necessarily. Equal DC resistance is a good sign, but it does not rule out all potential faults, such as turn-to-turn shorts, insulation weakness, magnetic issues, or mechanical problems.
Q6: What percentage of phase resistance imbalance is acceptable?
There is no single percentage that applies to all BLDC motors. The acceptable limit is specific to the motor's design and must be defined in the official product specification, taking into account the measurement method's uncertainty.
IEEE, *IEEE Std 112-2004: IEEE Standard Test Procedure for Polyphase Induction Motors and Generators*, Sections 3.2.2, 4.2 and 5.4. The standard addresses winding-resistance testing, instrument accuracy, terminal-pair measurements and temperature conditions. Its formal scope is polyphase induction machines rather than BLDC motor acceptance testing. ↩
Wikipedia, "Four-terminal sensing." Four-wire (Kelvin) measurement uses separate current-carrying and voltage-sensing connections to reduce errors caused by lead resistance and contact voltage drops outside the voltage-sensing points. It does not remove resistance within those points or other sources of measurement uncertainty. ↩
Wikipedia, "Electrical resistivity and conductivity," material-properties table and temperature-dependence discussion. The listed temperature coefficient for annealed copper is approximately 0.00393 K⁻¹ at 20°C. The value is approximate and depends on material properties and reference temperature. ↩
ATS Industrial Automation, "The Importance of Defining Acceptance Criteria in Automation Projects." The article recommends establishing objective pass/fail criteria, test specifications and acceptable limits before acceptance testing. It provides general industrial-automation guidance, not specific BLDC winding-resistance measurement requirements. ↩
Wikipedia, "Four-terminal sensing." The four-wire Kelvin method is suitable for checking low terminal-to-terminal resistance values, using separate current and voltage connections to reduce external lead and contact errors. In a BLDC motor test, each terminal pair must be measured under consistent conditions, with voltage-sensing points appropriately positioned. The source explains the measurement principle rather than a BLDC-specific testing procedure. ↩
SimpleFOC, "Phase resistance." The documentation distinguishes phase resistance from terminal-to-terminal resistance in three-phase BLDC motors and explains the conversions for balanced three-wire Star/Wye and Delta winding configurations. ↩
IRISS, "3 Phase Current Imbalance." The article discusses abnormal phase currents, motor heating and vibration as potential operating symptoms that warrant electrical and mechanical investigation. These observations do not, by themselves, establish a winding-resistance imbalance. ↩
IEEE Technology Navigator, "Average Winding Temperature." The resource describes the relationship between winding temperature and resistance and the use of resistance measurements at known temperatures to estimate winding temperature. This supports recording temperature when comparing winding-resistance readings. ↩